Showing 49–60 of 73 results

  • KOROMINERAL

    KOROMINERAL is a liquid, transparent impregnation on silicate basis for the improvement of mineral surfaces. Due to the increasing silicification, the cement matrix improves in the course of time. A significant improvement of the wear resistance is not possible.

  • KOROPOX

    KOROPOX is a 2-component, water emulsifiable, transparent impregnation on epoxy-resin basis (concentrate) to improve surfaces of mineral sub-bases. The penetration of liquids and other dirt is reduced. The surfaces are easier to clean and become increasingly shiny. The surface remains open to diffusion.

  • KOROCURE

    KOROCURE is a liquid temporary evaporation protection for intermediate curing. To protect the fresh concrete, depending on its grade, ambient and weather conditions, measures for intermediate curing should be taken acc. to DIN EN 13670:2011-03 in combination with DIN 1045-3:3012-03. The intermediate curing restrains the water in the concrete from evaporation, at wind and direct sun exposure. Thus, there is sufficient water in the concrete to allow the cement to hydrate properly.

  • KOROTEX

    KOROTEX is a liquid, solvent-free, acrylic resin dispersion that after drying produces a transparent and slightly shiny film that protects the industrial floor, concrete or cement screed, effectively from premature drying out and prevents possible damage (crack formation, surface damage) due to insufficient after-treatment.

  • GRANIDUR

    Use for polished, decorative screeds in sales rooms, museums, show rooms, boutiques, foyers, office and administrative buildings, restaurants, galleries etc.

  • GRANIDUR BIANCO/NERO

    Use for polished, decorative screeds in a middle layer thickness of 15 mm in sales rooms, museums, show rooms, boutiques, foyers, office and administrative buildings, restaurants, galleries etc.

  • KORODUR COPETTI FLOOR KCF

    KCF 05 and KCF 08 are installed in one or two layers acc. to

    • DIN 18560-2 screeds and heated screeds on insulation layer
    • DIN 18560-3 bonded screeds with KORODUR HB 5 bonding compound (see data sheet)
    • DIN 18560-4 screeds on separation layer

    KCF 05 is also available as fast-setting variant as KCF 05 rapid (with dimensionally stable binder on ternary basis).

  • NEODUR HE 40 and HE 40/8

    NEODUR HE 40 is a ready to use, cementitious hard aggregate screed on the basis of KORODUR hard aggregates acc. to DIN 1100 (group A) in the qualities

    • NEODUR HE 40: layer thickness fresh on fresh up to 15 mm
    • NEODUR HE 40: layer thickness as bonded screed up to 35 mm
    • NEODUR HE 40/8: layer thickness as bonded screed up to 50 mm

    Processing in one layer as bonded screed for heavy-duty stress acc. to DIN 18560-7.

  • NEODUR HE 65 plus SVS 3

    NEODUR HE 65 Plus is a ready to use, cementitious, synthetic-modified hard aggregate screed on the basis of KORODUR hard aggregates acc. to DIN 1100 (group A) in the qualtities

    • NEODUR HE 65 Plus:                    on the basis of KORODUR VS 0/5
    • NEODUR HE 65 Plus SVS 3:        on the basis of KORODUR WH-Special

    Installation in one layer as bonded screed for highest stress demands acc. to DIN 18560-7 on set base concrete without additional bonding compound. The bonding compound is produced from the same material, i.e. the NEODUR HE 65 Plus is applied in slurry consistency.

  • NEODUR HE 65 plus

    NEODUR HE 65 Plus is a ready to use, cementitious, synthetic-modified hard aggregate screed on the basis of KORODUR hard aggregates acc. to DIN 1100 (group A) in the qualtities

    • NEODUR HE 65 Plus:                    on the basis of KORODUR VS 0/5
    • NEODUR HE 65 Plus SVS 3:        on the basis of KORODUR WH-Special

    Installation in one layer as bonded screed for highest stress demands acc. to DIN 18560-7 on set base concrete without additional bonding compound. The bonding compound is produced from the same material, i.e. the NEODUR HE 65 Plus is applied in slurry consistency.

  • NEODUR HE 65 metallic

    NEODUR HE 65 metallic is a ready to use cementitious hard aggregate screed with metallic aggregates on the basis of KORODUR hard aggregates acc. to DIN 110 (group M) on the basis of KORODUR WH-metallic.

    Processing in one layer as bonded screed for heaviest stress demands acc. to DIN 18560-7.

  • NEODUR HE 65 SVS 1,5 extra

    NEODUR HE 65 SVS 1,5 extra is a ready to use cementitious hard aggregate screed on the basis of KORODUR hard aggregates.

    Processing in one layer as bonded screed for heaviest stress demands acc. to DIN 18560-7.

    Also available in colour, see KORODUR colour chart.